Take a look at this reconditioned stainless steel spreader just out of the shop.  There are more new parts than used parts on this one.  This unit has been sandblasted and painted with epoxy primer and urethane paint,.  All new bearings, hydraulic wheel actuation, new 540 PTO shaft, new ridge pole and tarp, new side apron gearboxes (updated to current production square gearboxes),  rebuilt fan gearbox, new frame assembly, new slowdown bracket, new distributor fan assembly, new sprockets, new splash guard, new fan gearbox bracket, new wheel drive tire, new gate guides,  new gate. etc.  You get the picture.   Tires are fair to good.  This spreader is in very good condition and is ready to start making you some money.  Cost:  $8,850

 

 

 

 

 

 ______________________________________________________________

If a cost effective smaller tender truck is what you are looking for, this Simonsen T320S (SN486288) might just be what you are looking for.  This is a stainless steel tender that has had the auger upgraded to a 20', SMC style auger.  The auger hopper, tube, and flighting are stainless steel.  The slide gate assembly has been replaced and upgraded to to stainless steel gate guides.  Auger bearing has been replace and the motor has been rebuilt.  This box is equipped with a manual Shur Lok roll tarp.  This tender is mounted on a good running International S series truck (12K front, 21K rear).  The engine is a DT466 (diesel, 230HP) and the transmission is a Fuller FS6406A.  Both are in good working condition.  Tires and brakes are good also.  This unit is ready to start working.  The asking price for this unit is $20,750.

 

 

 

 

 

 

  ___________________________________________________________________

Just out of the shop, this SMC2584Shyd 8 ton stainless steel spreader (serial number 208S14540) has just been reconditioned and is ready to go.  This spreader features hydraulic wheel actuation and hydraulic distributor fan.  This is a great setup if you are looking to spreader your own fertilizer.  There are no PTO shafts to bend or damage.  Just plug into your tractor hydraulics with the hydraulic apron chain wheel drive and hydraulic fan drive and you are good to go.  This spreader has been sandblasted, primed, and repainted.  The hydraulic motor and valves have been tested and rebuilt as necessary.  All new bearings have been installed as well as many other new parts.  The tires are in fair to good condition and the price includes a new tarp.  The cost of this unit is $8550.

 

 

 

 

 ___________________________________________________________________

 

Reconditioned SMC2584S eight ton spreader (serial number 102S13679) with a roll tarp.  This spreader features hydraulic wheel drive, stainless steel shell, and PTO drive on the distributor fan.  This spreader has been sandblasted, disassembled, new bearings installed, fan gearbox rebuilt, new distributor fan, new press wheel drive, new paint and decals.  There are many new parts on this spreader and it is in field ready condition.  Tires are in good condition and it needs nothing but a new owner.  The price on this unit is $8,900.  A really nice spreader at about half the price of new.

 

 

 

 

 

 

 

------------------------------------------------------------------------------------------------------------

 

2013 Isuzu 48HP 4 cylinder self-contained diesel engine drive for a side auger tender.  This engine has been checked, and is ready to run.  Hour meter shows 12 hours.  This engine was removed from a tender that was rolled onto its side.  Motor sustained no damage in the rollover.  Pump, oil tank, battery box, and plumbing are included.  Fuel tank is not included.  Sold as is in running condition.  Can hear run.

Price:  $5,500  SOLD!


 

 

 

 

___________________________________________________________________

 

 

Rebuilt feed body auger motor for sale.

Part #4769-00.  This motor is used on VA50-8, V70-8, VA50-6, V70-6, CA80-6 feed body vertical augers and VA50-8, and V70-8 delivery augers.  This motor is completely rebuilt with new seals.  The shaft is in very good condition.  It has been tested and is ready to bolt on.  Price $409.00.  2 available

 

Rebuilt feed body auger motor for sale.

Part #4770-00.  This motor is used on VA50-6 and V70-6 delivery augers.  It is also used on the VA50-9 floor auger.  This motor has been completely rebuilt with new seals, has been tested, and is ready to go.  Price is $346.50.  1 available.